CLS219 CL500 5.5 2010 - TRANSMISSION SLIPPAGE

A place for open-ended discussion on any car-related topic.
Post Reply
RogerSalesCar
Moderator
Posts: 132
Joined: Sat Aug 24, 2019 10:25 pm

To Whom It May Concern,

Win: WDD2193722A162059

Yesterday, the vehicle suddenly stopped accelerating and seemed to enter limp mode; I restarted it, but the problem persisted.
need to rev it up to 3,000+ to feel any movement
The care was able to be parked on the pavement and then winched onto the trailer. I called RAC and got home safely. Upon returning, I noticed a clear liquid on the floor.

As you can see in the photo below, the RAC patrol conducted diagnostics today.

I'm hoping it's just the ATF sump gasket or pilot bush because the vehicle has over 100,000 miles and I can't find any ATFS history.

I should prioritise identifying the source of the leak and increasing the level of care.

I'd prefer not to sell the car in its current condition, so I was hoping you could pass along some advice or information on this.

I appreciate it. As
MercedesMan98
Moderator
Posts: 321
Joined: Fri Mar 20, 2020 8:40 pm

Condensate from the air conditioning system was likely the clear liquid.

Mercedes typically uses coloured gearbox fluid, either red or blue.

Checking the ATF level should be the first order of business.
RogerSalesCar
Moderator
Posts: 132
Joined: Sat Aug 24, 2019 10:25 pm

I appreciate it.

I have not topped up the air conditioner while it was fully empty.

After the engine reaches a temperature of about 48 degrees Celsius, I will drain the ATF sump and inspect for sputtering to determine if the level is adequate.
MercedesMan98
Moderator
Posts: 321
Joined: Fri Mar 20, 2020 8:40 pm

Discovered this:

The method you are proposing seems to be 👍

7G-Tronic / 722.9 Inspection Process in Detail
While using a lift or jack stands, make sure the vehicle is level.
Check the Temperature: Turn on the Engine and Run It for a While. To bring the fluid up to the required check temperature, use a diagnostic scanner or infrared gun pointed at the gearbox pan. This temperature range is usually verified around 45°C-113°C via the internal overflow pipe, but it depends on the service specs. [1]
Rev Up the Engine: Put your foot firmly on the brake and gradually shift through gears (P - R - N - D) until you return to Park with the engine idling. Keep the vehicle moving. [1]
Verify the Overflow Plug:
Find the gearbox oil pan's overflow/drain plug at the pan's base.
Lift the center overflow plug out of the engine while it's running.
When the automatic gearbox fluid (ATF) reaches the correct expansion temperature, it should drip out in a small, steady stream. This is the correct level.
At the lowest level, there is no output. More fluid needs to be pumped into the pan using a fill adapter until it begins to drip out.
Once it reaches overflow, remove the plug and wait for the water to slow down to a trickle. values 1, 2, and 3
To reinstall, use a fresh plug or seal and tighten it to the manufacturer's recommended torque.
RogerSalesCar
Moderator
Posts: 132
Joined: Sat Aug 24, 2019 10:25 pm

I will, thank you.prioritise this.
I will report back during the week.
MercedesMan98
Moderator
Posts: 321
Joined: Fri Mar 20, 2020 8:40 pm

Please tell me it's not something complicated. 🤐
RogerSalesCar
Moderator
Posts: 132
Joined: Sat Aug 24, 2019 10:25 pm

I am truly grateful.I wish it were so, because I am not planning to shell out a pretty penny.
Post Reply